Most viewed - guyfawkes041's Gallery |
Contents of DIY Handlining Reel Compartment475 views
|
|
DIY CANOE PACK 1338 views
|
|
DIY CANOE PACK 2329 views
|
|
DIY CANOE PACK FOR BARRELS300 viewsSnaps of my home-made canoe pack for carrying screw top buckets and other things.
|
|
WITH LOAD AND AIR FLOTATION BAGS153 viewsA picture of my canoe with tripping load and airbags installed prior to installation of a spray deck.
|
|
DIY ULTRALIGHT FOLDING REFLECTOR OVEN 6144 viewsOblique view of assembled reflector oven.
Total cost <$5, total weight < 5oz, total time to construct <30 mins.
|
|
Detail of DIY Handlining Rig143 views
|
|
DIY ULTRALIGHT FOLDING REFLECTOR OVEN 4139 viewsI got the idea for this folding reflector oven from a Youtube video. It is capable of baking a bannock for two to accompany a meal. It weighs only a few ounces, and I have used it fairly heavily over a total of about 2 months of tripping.
|
|
DIY ULTRALIGHT FOLDING REFLECTOR OVEN 3138 viewsThe reflector oven is made from a Dollar Store oven drip pan with holes strategically placed in it for the ACCO Fasteners and skewers. The skewer holes have been lined with small brass grommets.
|
|
DETAILS OF PADDLE GARAGE134 viewsA close view of the paddle garage, which holds the blade ends of the spare paddles onto the spray deck in the event of a dump.
|
|
DIY ULTRALIGHT FOLDING REFLECTOR OVEN 5133 viewsSide view of assembled reflector oven. I use rocks or firewood to prop up the rear of it, to level the baking tray. Depending on the fire, it takes about 15 minutes to cook a bannock the size of a baby's head.
|
|
FORWARD PORTION OF SPRAY DECK132 viewsA view focused on the details of the fore deck.
|
|
DETAILS OF FRONT DECK WATER DIVERTER130 viewsA snap showing details of the articulating water diverter which will float upward as waves deepen, and channel water off to the sides instead of into the open center portion of the canoe. An experiment.
|
|
124 viewsNew DIY spray deck made from repurposed tent liner fitted over tripping load and air flotation bags.
|
|
DIY Handlining Kit Components124 views2cnd of 4 pics, this shows the separate components of the DIY Handlining Kit.
|
|
120 views
|
|
CLOSE VIEW OF BACK OF DIY PIN KIT POUCH FOR PFD110 viewsThe pouch contains a large tubular anchor sling, a medium tubular anchor sling, a large climbing pulley, 2 smaller prussik minding climbing pulleys, 2 prussiks, and 3 locking carabiners. A fourth locking carabiner connects a 75' throwbag to the 25' rear painter on the canoe, and laminated Z Drag instructions are held in an interior pocket of the PFD.
|
|
108 views
|
|
Packed DIY Handlining kit108 viewsFirst of 4 pics, this shows the kit as it sits in my canoe pack.
|
|
DIY PIN KIT CARRIER ON PFD107 viewsA home made, low profile, quick draining zippered pouch attached to the rear of a Kokatat Maximus Prime PFD, for carrying a well put together pin kit.
|
|
SIDE VIEW OF DIY PIN KIT CARRIER FOR PFD106 viewsThe pouch is fabricated from rubberized linen mesh, with all seams double-stitched and binding, and grommets for attachment points line the edges. It is secured to the PFD above the rescue harness, by paracord at 4 corners.
|
|
102 views
|
|
101 views
|
|
101 views
|
|
MY TARP PITCH93 viewsA view of my standard lean-to with center pole tarp pitch
|
|
DIY ULTRALIGHT FOLDING REFLECTOR OVEN 187 viewsDIY Folding reflector oven in its case
|
|
DIY ULTRALIGHT FOLDING REFLECTOR OVEN 284 viewsThe case carries the folded oven, a baking tray, 2 ACCO Fasteners, and 2 modified BBQ skewers.
|
|
BLUEWATER FREEDOM TRIPPER 17 FLOAT TANK 169 views
|
|
|
|
|